| Unfinished Wood
| Non Tempered Masonite |
Drywall |
|
Adhesive(s} that may be used on this suiface< |
- Mineral Based Contact Adhesive
- Water Based Contact Adhesive
- White Glues
- Carpet Cement
- Rubber Based Hot Melt Adhesive
|
- Mineral Based Contact Adhesive
- Water Based Contact Adhesive
- White Glues
- Carpet Cement
- Rubber Based Hot Melt Adhesive
|
- Mineral Based Contact Adhesive
- Water Based Contact Adhesive
- White Glues
- Carpet Cement
|
| Preparation |
- Surface should first
be sealed.
- Adhesives may be used as a
sealer...let dry for 24 hours.
- For maximum adhesion, apply
adequate sealer to fill the
"valleys" of the surface.
|
- Surface should first
be sealed.
- Adhesives may be used as a
sealer...let dry for 24 hours.
|
- Surface should first
be sealed.
- Adhesives may be used as a
sealer...let dry for 24 hours.
|
| Application |
- Adhesives should only be applied to
the surface, never to the fabric.
- This is a directional fabric.
Hang each strip in the same
direction to avoid color
differences caused by pile
directional changes.
- If using a roller, apply a light
coat of adhesive to the surface to
avoid bleed through to the face of the
fabric. Adhesive may also be brushed or sprayed
onto the surface.
- White glues with a high viscosity
(liquidity) should be allowed set-up time
before applying fabric to avoid bleed through.
You may want to use tacks to hold fabric in place.
Allow applied fabric 24 hours to cure.
|
- Adhesives should only be applied to
the surface, never to the fabric.
- This is a directional fabric.
Hang each strip in the same
direction to avoid color
differences caused by pile
directional changes.
- If using a roller, apply a light
coat of adhesive to the surface to avoid
bleed through to the face of the fabric.
Adhesive may also be brushed or sprayed
onto the surface.
- White glues with a high
viscosity (liquidity) should be
allowed set-up time before
applying fabric to avoid bleed through.
You may want to use tacks to hold fabric in place.
Allow applied fabric 24 hours to cure.
|
- Adhesives should only be applied
to the surface, never to the fabric.
- This is a directional fabric.
Hang each strip in the same
direction to avoid color
differences caused by pile
directional changes.
- If using a roller, apply a light
coat of adhesive to the surface to
avoid bleed through to the face of
the fabric. Adhesive may also
be brushed or sprayed onto the surface.
- White glues with a high
viscosity (liquidity) should be
allowed set-up time before applying
fabric to avoid bleed through.
You may want to use tacks to hold fabric in place.
Allow applied fabric 24 hours to cure.
|
| Installation Alerts or other Miscellaneous Information |
- Hot melt adhesives set-up
quickly, usually used in
production line set-up.
- Mineral based adhesives
are not recommended for
unventilated areas in offices,
museums, showrooms, etc.
- Remove excess adhesive
immediately after each seam
is completed using a water
dampened sponge, if applicable.
|
- Hot melt adhesives set-up
quickly, usually used in
production line set-up.
- Surface preparation will help in
the later removal of the fabric.
- When removing, if a water
based adhesive was used,
soaking or steaming will help
loosen the adhesive.
- Mineral based adhesives
are not recommended for
unventilated areas in offices,
museums, showrooms, etc.
- Remove excess adhesive
immediately after each seam
is completed using a water
dampened sponge, if applicable.
|
- Surface preparation will help in
the later removal of the fabric.
- When removing, if a water
based adhesive was used,
soaking or steaming will help
loosen the adhesive.
- Mineral based adhesives
are not recommended for
unventilated areas in offices,
museums, showrooms, etc.
- Remove excess adhesive
immediately after each seam
is completed using a water
dampened sponge, if applicable.
|
